thermostat with Oled display

elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Michal81 wrote: Sat Feb 29, 2020 3:18 pm Help.
Elmay, can you tell me the reasons for the Error message when converting the USB power supply to the power supply?
Connected as in the picture:
the ERROR Conimukat appears

What is this, what does it mean?
The display shows errors as "E" with a number.
Michal81
Posts: 153
Joined: Sun Feb 02, 2020 9:03 pm

elmaya wrote: Sat Feb 29, 2020 3:47 pm
Michal81 wrote: Sat Feb 29, 2020 3:18 pm Help.
Elmay, can you tell me the reasons for the Error message when converting the USB power supply to the power supply?
Connected as in the picture:
the ERROR Conimukat appears

What is this, what does it mean?
The display shows errors as "E" with a number.
I am sorry if I described it poorly.
The ERROR message appears.
Attachments
20200229_170720.jpg
20200229_170720.jpg (2.1 MiB) Viewed 4315 times
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

What cable length do you have for DS18B20?
test with a lower resistor of 2,2kohm for the DS18B20 probe.
Michal81
Posts: 153
Joined: Sun Feb 02, 2020 9:03 pm

80 cm long nan sensor cable.
A resistor like the three design in the first post 4.7 kohm.
Are you suggesting inserting a smaller 2.2kohm ??
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

yes, reduce the resistance of 4,7koh or use 2 in parallel,
you have a problem of electrical derivation, you can also connect the GND of the wemos to earth.
Perhaps it is also possible to solve it by turning the plug around (220v).
Michal81
Posts: 153
Joined: Sun Feb 02, 2020 9:03 pm

elmaya - Is it possible for a cannon project with e.g. a display like this: https://pl.aliexpress.com/item/32994189 ... hweb201603_
I think it would be clearer and more readable than Oled.

By the way - a tile is created.Of course, this is still a small fix.
Everything can be assembled from ready elements and modules.
How it will come and act - I will have a pair to give away.
Of course, I'd like to put a 20x4 display .... lol ..
Attachments
płytka.jpg
płytka.jpg (134.07 KiB) Viewed 4259 times
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

What and how do you want to see on the 20x4 Display?
Michal81
Posts: 153
Joined: Sun Feb 02, 2020 9:03 pm

I think I wrote the other way around. it was about 4x16 lib 4x20. I think that what is enough for the Oled display, but spread over 4 lines. This display seems to me to be more readable.
For example :
1. CURRENT TEMPERATURE: ----.
2. REQUIRED TEMPERATURE: ----.
3.WORK MODE: MANUAL / AUTOMATIC
4. DEVICE STATUS: On / Off, next to WiFi network status

Illustrative image:
Attachments
Screenshot_20200302-184053_Opera.jpg
Screenshot_20200302-184053_Opera.jpg (141.2 KiB) Viewed 4249 times
User avatar
Daro1003
Posts: 114
Joined: Fri Jan 18, 2019 6:22 am

Hello
I built a thermostat based on soft: Supla_Termostst_oled_H_C_0_96_DOUT_16Mbit.bin with display.
Everything works, unfortunately, the display is dead. The displays have two pieces with SCK and SDA markings probably because if I can ask you to generate a bin file for these displays I do not want to throw them in the bin because they will not be useful for anything else.
eradek
Posts: 81
Joined: Sun Sep 09, 2018 5:32 pm

Michal81 wrote: Mon Mar 02, 2020 4:14 pm By the way - a tile is created.Of course, this is still a small fix.
Can you share GERBER for the tile?
Post Reply

Return to “Ideas and concepts”