How to get Supla devices in Home Assistant without MQTT?
-
- Posts: 15
- Joined: Mon Jun 26, 2023 5:51 am
Hi pzygmunt. Just wanted to say a huge thank you for getting my Supla heater working in HA. I think the issue I had was not being able to SSH into HA to setup the conf file.
-
- Posts: 19039
- Joined: Tue Jan 19, 2016 9:26 am
- Location: Paczków
Is everything working as you expected now?
-
- Posts: 2
- Joined: Sat Jan 13, 2024 8:39 pm
EDIT:
Hello, I am looking for a help how to use SUPLA (ZAMEL SRW-01 for blinds control) in Home Assistant if I already have MQTT set up for another device. The other device connects to the Mosqitto broker via local network to port 1883. When I setup the MQTT as described for supla, will I loose the other device connection?
Also, can I use the SRW-01 with the local only mqtt and not use supla cloud at all ? Is there any tutorial for this local LAN sollution?
Hello, I am looking for a help how to use SUPLA (ZAMEL SRW-01 for blinds control) in Home Assistant if I already have MQTT set up for another device. The other device connects to the Mosqitto broker via local network to port 1883. When I setup the MQTT as described for supla, will I loose the other device connection?
Also, can I use the SRW-01 with the local only mqtt and not use supla cloud at all ? Is there any tutorial for this local LAN sollution?
-
- Posts: 19039
- Joined: Tue Jan 19, 2016 9:26 am
- Location: Paczków
There are 3 scenarios to choose from:
1. Connect mqttX.supla.org to your broker (bridge mode)
2. Connect the HA to mqttX.supla.org
3. Connect SRW directly to your local broker.
Instructions for 1 and 2 https://drive.google.com/file/d/10HTT6j ... KQwb3/view
In the case of point 3, switch SRW to configuration mode, and then on page http://192.168.4.1 change the protocol from Supla to MQTT.
1. Connect mqttX.supla.org to your broker (bridge mode)
2. Connect the HA to mqttX.supla.org
3. Connect SRW directly to your local broker.
Instructions for 1 and 2 https://drive.google.com/file/d/10HTT6j ... KQwb3/view
In the case of point 3, switch SRW to configuration mode, and then on page http://192.168.4.1 change the protocol from Supla to MQTT.
-
- Posts: 2
- Joined: Sat Jan 13, 2024 8:39 pm
Hello, thank you, I will go with the option no 3.
I was able to setup SRW-01 to mqtt mode.
Now, what I must do on the homeassistant side to control the blinds?
EDIT: Ok, it is working, no action necessary on the HA side, auto discovery works fine
I was able to setup SRW-01 to mqtt mode.
Now, what I must do on the homeassistant side to control the blinds?
EDIT: Ok, it is working, no action necessary on the HA side, auto discovery works fine
-
- Posts: 19039
- Joined: Tue Jan 19, 2016 9:26 am
- Location: Paczków
SBW-02 nemá na palubě MQTT, ale pokud jej připojíte z cloud.supla.org, bude k dispozici prostřednictvím brokera MQTT mqttX.supla.org.
-
- Posts: 4
- Joined: Thu May 16, 2024 1:54 pm
Ano, ale mám již jiné přístoje na Zigbee2mqtt - Mosquito Broker.
Je nějaké řešení, jak dostat do HA tento ZAMEL SBW-02?
Je nějaké řešení, jak dostat do HA tento ZAMEL SBW-02?
Last edited by Star_Mann on Fri May 17, 2024 9:47 am, edited 2 times in total.
-
- Posts: 19039
- Joined: Tue Jan 19, 2016 9:26 am
- Location: Paczków
Nemusíte se vzdávat vlastního brokera. Můžete vytvořit most mezi svým vlastním brokerem a mqttX.supla.org